Found 22 Business Products.
The AAI-NIS2 works with XM/Sirius Satellite ready Infiniti and Nissan factory radios. It allows audio from devices like Apple's iPod¿, VCP, MP3 players, Portable CD players, DVD players or aftermarket satellite receivers to play through the stock stereo system. It has two auxiliary inputs which are selected by the SAT/Radio button on face of radio. The AAI-NIS2 Utilizes the steering wheel or radio buttons to send out commands to PAC's optional SWI-X which can be used to control an MP3 player, DVD, VCP or most devices that use an infrared remote. The AAI-NIS2 also comes with negative remote output which can be used to turn on devices when ever the radio is in Aux1 mode.
Get Price
The display shows the distance of the object in feet. Left and right cursors show the left and right distance range. Four ultrasonic sensors mount on the rear bumper, and they are activated when the driver puts their vehicle into reverse. Two sensors mount on the front bumper, and they are activated when the car drives forward and is breaking. A drill bit for the size of the sensor is included.
Get Price
The system will beep based on the distance of an object behind the car. The display shows the distance of the object behind the car. Left and right cursors show the left and right distance range. The device is only activated when the driver puts their vehicle into reverse. Four ultrasonic sensors mount on your bumper. A drill bit for the size of the sensor is included. Installation Step 1: Connect the Electric Power Open the trunk, find the wires to the back light housing. Use of a 12 volt multi-meter, Probe the appropriate wiring harness which heads toward the reverse light connector of the vehicle, looking for the wire which carries 12 volts + when reverse gear is engaged, and no voltage when reverse gear is disengaged. Never use a test light to probe wires. Step 2: Install the Backup Sensors in the bumper Drill four holes in the bumper via provided drilling bit. Install the insert-style sensors in the bumper. Run the wires of sensors into the trunk, and plug in the control center. Connect the power line of control center with the power line of backup light
Get Price
The system will beep based on the distance of an object behind the car. There is no display unit, so it is very easy to install. The device is only activated when the driver puts their vehicle into reverse. Two ultrasonic sensors mount on your bumper or the license plate with a special holder that is free, but need to request when place an order. A drill bit for the size of the sensor is included. Installation Step 1: Connect the Electric Power Open the trunk, find the wires to the back light housing. Use of a 12 volt multi-meter, Probe the appropriate wiring harness which heads toward the reverse light connector of the vehicle, looking for the wire which carries 12 volts + when reverse gear is engaged, and no voltage when reverse gear is disengaged. Never use a test light to probe wires. Using a quick connector (included) to connect the reverse light power wire (+12) with the RED wire from the control center. You do not need to cut any wire. Step 2: Install the Backup Sensors In Bumper Drill two holes in the bumper via provided drilling bit. Install the insert-style sensors in the bumper. Run the wires of sensors into the trunk, and plug in the control center. Connect the power line of control center with the power line of backup light On the License Plate Drill two holes through the license plate and the trunk. Install two insert-style sensors with the special housings on the license plate as the picture shown. Run the wires of sensors into the trunk, and plug in the control center. (Note: The license plate holders are available for the two drill-in sensors version of the backup sensors system. Normally the sensors are in white since most of license plates are in white. They are free of charge. If you need them, please write a request on the comment field when place an order.)
Get Price
Need a business card that really packs a punch? These heavyweight matte-coated Business Cards deliver vivid, high-resolution text and graphics that will impress colleagues and prospective clients. Simply take a tour of the Business Resource Center at avery.com to find and format free templates and then print them from your inkjet printer in minutes. This business card solution is truly a knockout. Convenient do-it-yourself cards mean that you can make changes and print new cards at a moment's notice. Heavyweight, high-quality card stock for a lasting professional appearance. Design and print business cards from your desktop in minutes. Print up to 10 cards per sheet. Compatible with inkjet printers. Customize and print using free templates from avery.com. Avery printable business cards are thick and customizable and deliver superior, professional-looking print quality.
Get Price
The system will beep based on the distance of an object behind the car. There is no display unit, so it is very easy to install. The device is only activated when the driver puts their vehicle into reverse. Two ultrasonic sensors mount on your bumper or the license plate with a special holder that is free, but need to request when place an order. A drill bit for the size of the sensor is included. Installation Step 1: Connect the Electric Power Open the trunk, find the wires to the back light housing. Use of a 12 volt multi-meter, Probe the appropriate wiring harness which heads toward the reverse light connector of the vehicle, looking for the wire which carries 12 volts + when reverse gear is engaged, and no voltage when reverse gear is disengaged. Never use a test light to probe wires. Using a quick connector (included) to connect the reverse light power wire (+12) with the RED wire from the control center. You do not need to cut any wire. Step 2: Install the Backup Sensors In Bumper Drill two holes in the bumper via provided drilling bit. Install the insert-style sensors in the bumper. Run the wires of sensors into the trunk, and plug in the control center. Connect the power line of control center with the power line of backup light On the License Plate Drill two holes through the license plate and the trunk. Install two insert-style sensors with the special housings on the license plate as the picture shown. Run the wires of sensors into the trunk, and plug in the control center. (Note: The license plate holders are available for the two drill-in sensors version of the backup sensors system. Normally the sensors are in white since most of license plates are in white. They are free of charge. If you need them, please write a request on the comment field when place an order.)
Get Price
The display shows the distance of the object in feet. Left and right cursors show the left and right distance range. Four ultrasonic sensors mount on the rear bumper, and they are activated when the driver puts their vehicle into reverse. Two sensors mount on the front bumper, and they are activated when the car drives forward and is breaking. A drill bit for the size of the sensor is included.
Get Price
The system will beep based on the distance of an object behind the car. There is no display unit, so it is very easy to install. The device is only activated when the driver puts their vehicle into reverse. Two ultrasonic sensors mount on your bumper or the license plate with a special holder that is free, but need to request when place an order. A drill bit for the size of the sensor is included. Installation Step 1: Connect the Electric Power Open the trunk, find the wires to the back light housing. Use of a 12 volt multi-meter, Probe the appropriate wiring harness which heads toward the reverse light connector of the vehicle, looking for the wire which carries 12 volts + when reverse gear is engaged, and no voltage when reverse gear is disengaged. Never use a test light to probe wires. Using a quick connector (included) to connect the reverse light power wire (+12) with the RED wire from the control center. You do not need to cut any wire. Step 2: Install the Backup Sensors In Bumper Drill two holes in the bumper via provided drilling bit. Install the insert-style sensors in the bumper. Run the wires of sensors into the trunk, and plug in the control center. Connect the power line of control center with the power line of backup light On the License Plate Drill two holes through the license plate and the trunk. Install two insert-style sensors with the special housings on the license plate as the picture shown. Run the wires of sensors into the trunk, and plug in the control center. (Note: The license plate holders are available for the two drill-in sensors version of the backup sensors system. Normally the sensors are in white since most of license plates are in white. They are free of charge. If you need them, please write a request on the comment field when place an order.)
Get Price
The display shows the distance of the object in feet. Left and right cursors show the left and right distance range. Four ultrasonic sensors mount on the rear bumper, and they are activated when the driver puts their vehicle into reverse. Two sensors mount on the front bumper, and they are activated when the car drives forward and is breaking. A drill bit for the size of the sensor is included.
Get Price
The system will beep based on the distance of an object behind the car. The display shows the distance of the object behind the car. The device is only activated when the driver puts their vehicle into reverse. Two ultrasonic sensors mount on your bumper or the license plate with a special holder. A drill bit for the size of the sensor is included. Installation Step 1: Connect the Electric Power Open the trunk, find the wires to the back light housing. Use of a 12 volt multi-meter, Probe the appropriate wiring harness which heads toward the reverse light connector of the vehicle, looking for the wire which carries 12 volts + when reverse gear is engaged, and no voltage when reverse gear is disengaged. Never use a test light to probe wires. Using a quick connector (included) to connect the reverse light power wire (+12) with the RED wire from the control center. You do not need to cut any wire. Step 2: Install the Backup Sensors In Bumper Drill two holes in the bumper via provided drilling bit. Install the insert-style sensors in the bumper. Run the wires of sensors into the trunk, and plug in the control center. Connect the power line of control center with the power line of backup light On the License Plate Drill two holes through the license plate and the trunk. Install two insert-style sensors with the special housings on the license plate as the picture shown. Run the wires of sensors into the trunk, and plug in the control center. (Note: The license plate holders are available for the two drill-in sensors version of the backup sensors system. Normally the sensors are in white since most of license plates are in white. They are free of charge. If you need them, please write a request on the comment field when place an order.)
Get Price
Top Search
Last Search
